World Library  
Flag as Inappropriate
Email this Article


An American Aviation AA-1 Yankee being refueled with 100LL avgas.

Avgas (aviation gasoline), also known as aviation spirit in the UK, is an aviation fuel used in spark-ignited internal-combustion engines to propel aircraft. Avgas is distinguished from mogas (motor gasoline), which is the everyday gasoline used in motor vehicles and some light aircraft. Unlike mogas, which has been formulated since the 1970s to allow the use of platinum-content catalytic converters for pollution reduction, avgas contains tetraethyl lead (TEL), a toxic substance used to prevent engine knocking (detonation).

Turbine and diesel engines are designed to use kerosene-based jet fuel.


The main petroleum component used in blending avgas is alkylate, which is essentially a mixture of various isooctanes. Some refineries also use reformate. All grades of avgas that meet CAN 2-3, 25-M82 have a density of 6.01 lb/U.S. gal at 15°C, or 0.721 kg/l. (6 lb/U.S. gal is commonly used for weight and balance computation.)[1] Density increases to 6.41 lb/US gallon, or 0.769 kg/l, at -40°C, and decreases by about 0.1% per 1C° (1.8F°) increase in temperature.[2] [3] Avgas has an emission coefficient (or factor) of 18.355 pounds CO2 per U.S. gallon (2.1994 kg/l)[4][5] or about 3.05 units of weight CO2 produced per unit weight of fuel used. Avgas has a lower and more uniform vapor pressure than automotive gasoline so it remains in the liquid state despite the reduced atmospheric pressure at high altitude, thus preventing vapor lock.

The particular mixtures in use today are the same as when they were first developed in the 1940s, and were used in airline and military aero engines with high levels of supercharging; notably the Rolls-Royce Merlin engine used in the Spitfire and Hurricane fighters, Mosquito fighter-bomber and Lancaster heavy bomber (the Merlin II and later versions required 100-octane fuel), as well as US-made liquid-cooled Allison V-1710 engines, and numerous radial engines from Pratt & Whitney, Wright, and other manufacturers on both sides of the Atlantic. The high octane ratings are achieved by the addition of TEL, a highly toxic substance that was phased out of automotive use in most countries in the late 20th century.

Avgas is currently available in several grades with differing maximum lead concentrations. Because TEL is an expensive and polluting ingredient, the minimum amount needed to bring the fuel to the required octane rating is used; actual concentrations are often lower than the permissible maximum. Historically, many post-WWII developed, low-powered 4- and 6-cylinder piston aircraft engines were designed to use leaded fuels; a suitable unleaded replacement fuel has not yet been developed and certified for most of these engines. As of 2011, numerous certificated reciprocating-engine aircraft require high-octane (leaded) fuels.

Jet fuel is similar to kerosene and is used in turbine engines; it is not avgas. Confusion can be caused by the terms Avtur and AvJet being used for jet fuel. In Europe, environmental and cost considerations have led to increasing numbers of aircraft being fitted with fuel-efficient diesel engines that run on jet fuel. Civilian aircraft use Jet-A, Jet-A1, or in severely cold climates Jet-B. There are other classification systems for military turbine and diesel fuel.


The annual US usage of avgas was 186 million US gallons (700,000 m3) in 2008, and was approximately 0.14% of the motor gasoline consumption. From 1983 through 2008, US usage of avgas declined consistently by approximately 7.5 million US gallons (28,000 m3) each year.[6]

As of 2008, the main consumers of avgas are in North America, Australia, Brazil, and Africa (mainly South Africa). Care must be taken by small airplane pilots to select airports with avgas on flight planning. For example, US and Japanese recreational pilots ship and depot avgas before flying into Siberia. Shrinking availability of avgas drives usage of small airplane engines that can use jet fuel.

In Europe, avgas remains the most common fuel; prices are so high that there have been efforts to convert to diesel fuel which is common, inexpensive, and has advantages for aviation use.


Many grades of avgas are identified by two numbers associated with its Motor Octane Number (MON).[7] The first number indicates the octane rating of the fuel tested to "aviation lean" standards, which is similar to the anti-knock index or "pump rating" given to automotive gasoline in the US. The second number indicates the octane rating of the fuel tested to the "aviation rich" standard, which tries to simulate a supercharged condition with a rich mixture, elevated temperatures, and a high manifold pressure. For example, 100/130 avgas has an octane rating of 100 at the lean settings usually used for cruising and 130 at the rich settings used for take-off and other full-power conditions.[8]

Additives such as TEL help to control detonation and provide lubrication. One gram of TEL contains 600 milligrams of lead.

Table of aviation fuel grades
Grade Colour (Dye) Lead (Pb) content maximum (g/L) Additives Uses Availability
80/87 ("avgas 80") red
(red + a little blue)
0.14 TEL It was used in engines with low compression ratio. Phased out in the late 20th century. Its availability is very limited.
82UL purple
(red + blue)
0 ASTM D6227; similar to automobile gasoline but without automotive additives As of 2008, 82UL is not being produced and no refiner has announced plans to put it into production.[9][10]
85UL none 0 oxygenate-free Used to power piston-engine ultralight aircraft.
Motor Octane Number min 85. Research Octane Number min 95.[11]
91/96 brown[12]
(orange + blue + red)
almost negligible TEL Made particularly for military use.
91/96UL none 0 ethanol-free, antioxidant and antistatic additives;[13] ASTM D7547 In 1991, Hjelmco Oil introduced unleaded avgas 91/96UL (also meeting leaded grade 91/98 standard ASTM D910 with the exception of transparent colour) and no lead in Sweden. Engine manufacturers Teledyne Continental Motors, Textron Lycoming, Rotax, and radial engine manufacturer Kalisz have cleared the Hjelmco avgas 91/96UL which in practice means that the fuel can be used in more than 90% of the piston aircraft fleet worldwide.[14][15][16][17] May be used in Rotax engines,[18] and Lycoming engines per SI1070R.[19] In November 2010, the European Aviation Safety Agency (EASA) based on about 20 years of trouble-free operations with unleaded avgas 91/96UL produced by Hjelmco Oil cleared this fuel for all aircraft where the aircraft engine manufacturer has approved this fuel.[20]
B91/115 green
(yellow + blue)
1.60 TEL; see standard GOST 1012-72.[21] Specially formulated for Shvetsov ASh-62 and Ivchenko AI-14 – nine-cylinder, air-cooled, radial aircraft engines. The Commonwealth of Independent States, produced exclusively by OBR PR.
100LL blue 0.3-0.56 g/l TEL
As of January 2010, 100LL has 1.2 to 2 grams TEL[22] per US gallon.
Most commonly used aviation gasoline. Pretty much worldwide
100/130 green
(yellow + blue)
1.12 TEL Mostly replaced by 100LL. As of August 2013, Australia, New Zealand, Chile, and the states of Hawaii and Utah in the United States.
G100UL none 0 aromatic compounds such as xylene or mesitylene Composed primarily of aviation alkylate (same as used for 100LL). As of August 2013, limited quantities are produced for testing.
115/145 ("avgas 115") purple
(red + blue)
TEL Originally used as primary fuel for the largest, boost-supercharged radial engines needing this fuel's anti-detonation properties.[23] Limited batches are produced for special events such as unlimited air races.

100LL (blue)

100LL is pronounced "one hundred low lead". It contains about one-half the TEL allowed in 100/130 (green), though the amount is about 4 times what was in leaded automotive grade.

Many Continental and Lycoming light airplane engines designed for 80/87 remain in production. Engines designed for 80/87 and not for 100LL might have lead buildup and lead fouling of the spark plugs if 100LL is used.

Some of the lower-powered (100–150 horsepower or 75–112 kilowatts) aviation engines that were developed in the late 1990s are designed to run on unleaded fuel and on 100LL, an example being the Rotax 912.[14]

Automotive gasoline

Automotive gasoline — known as mogas or autogas among aviators — that does not contain ethanol may be used in certified aircraft that have a Supplemental Type Certificate for automotive gasoline as well as in experimental aircraft and ultralight aircraft. Some oxygenates other than ethanol are approved. Most of these applicable aircraft have low-compression engines which were originally certified to run on 80/87 avgas and require only "regular" 87 anti-knock index automotive gasoline. Examples include the popular Cessna 172 Skyhawk or Piper Cherokee with the 150 hp (110 kW) variant of the Lycoming O-320.

Some aircraft engines were originally certified using a 91/96 avgas and have STCs available to run "premium" 91 anti-knock index (AKI) automotive gasoline. Examples include some Cherokees with the 160 hp (120 kW) Lycoming O-320 or 180 hp (130 kW) O-360, or the Cessna 152 with the O-235. The AKI rating of typical automotive fuel does not directly correspond to the 91/96 avgas used to certify engines. Sensitivity is roughly 8-10 points meaning that a 91 AKI fuel might have a MON of as low as 86. The extensive testing process required to obtain an STC for the engine/airframe combination helps ensure that for those eligible aircraft, 91 AKI fuel provides sufficient detonation margin under normal conditions.

Automotive gasoline is not a fully viable replacement for avgas in many aircraft, because many high-performance and/or turbocharged airplane engines require 100 octane fuel and modifications are necessary in order to use lower-octane fuel.[24] [25]

Many general aviation aircraft engines were designed to run on 80/87 octane, roughly the standard for North American automobiles today. Direct conversions to run on automotive fuel are fairly common and applied via the supplemental type certificate (STC) process. However, the alloys used in aviation engine construction are chosen for their durability and synergistic relationship with the protective features of lead, and engine wear in the valves is a potential problem on automotive gasoline conversions.

Fortunately, significant history of engines converted to mogas has shown that very few engine problems are caused by automotive gasoline. A larger problem stems from the higher and wider range of allowable vapor pressures found in automotive gasoline; this can pose some risk to aviation users if fuel system design considerations are not taken into account. Automotive gasoline can vaporize in fuel lines causing a vapor lock (a bubble in the line) or fuel pump cavitation, starving the engine of fuel. This does not constitute an insurmountable obstacle, but merely requires examination of the fuel system, ensuring adequate shielding from high temperatures and maintaining sufficient pressure in the fuel lines. This is the main reason why both the specific engine model as well as the aircraft in which it is installed must be supplementally certified for the conversion. A good example of this is the Piper Cherokee with high-compression 160 or 180 hp (120 or 130 kW) engines. Only later versions of the airframe with different engine cowling and exhaust arrangements are applicable for the automotive fuel STC, and even then require fuel-system modifications.

Vapor lock typically occurs in fuel systems where a mechanically-driven fuel pump mounted on the engine draws fuel from a tank mounted lower than the pump. The reduced pressure in the line can cause the more volatile components in automotive gasoline to flash into vapor, forming bubbles in the fuel line and interrupting fuel flow. If an electric boost pump is mounted in the fuel tank to push fuel toward the engine, as is common practice in fuel-injected automobiles, the fuel pressure in the lines is maintained above ambient pressure, preventing bubble formation. Likewise, if the fuel tank is mounted above the engine and fuel flows primarily due to gravity, as in a high-wing airplane, vapor lock cannot occur, using either aviation or automotive fuels. Fuel-injected engines in automobiles also usually have a "fuel return" line to send unused fuel back to the tank, which has the benefit of equalizing the fuel's temperature throughout the system, further reducing the chance for vapor lock from developing.

In addition to vapor locking potential, automotive gasoline does not have the same quality tracking as aviation gasoline. To help solve this problem, the specification for an aviation fuel known as 82UL was developed as essentially automotive gasoline with additional quality tracking and restrictions on permissible additives. This fuel is not currently in production and no refiners have committed to producing it.[10]


Rotax allows up to 10% ethanol (similar to E10 fuel for cars) in the fuel for Rotax 912 engines. Light sport aircraft that are specified by the manufacturer to tolerate alcohol in the fuel system can use up to 10% ethanol.[14]

Fuel dyes

Fuel dyes aid ground crew and pilots in identifying and distinguishing the fuel grades[9] and most are specified by ASTM D910 or other standards.[12] Dyes for the fuel are required in some countries.[26]

Table of aviation fuel dyes
Dye (nominal colour) chemical
blue 1,4-dialkylaminoanthraquinone
yellow p-diethylaminoazobenzene or 1,3-benzenediol 2,4-bis [(alkylphenyl)azo-]
red alkyl derivatives of azobenzene-4-azo-2-naphthol
orange benzene-azo-2-napthol

Phase-out of leaded aviation gasoline

The 100LL phase-out has been called "one of modern GA's most pressing problems",[27] because 70% of 100LL aviation fuel is used by the 30% of the aircraft in the general aviation fleet that cannot use any of the existing alternatives.[28][29][30]

In February 2008, Teledyne Continental Motors (TCM) announced that the company is very concerned about future availability of 100LL, and as a result, they would develop a line of diesel engines.[31] In a February 2008 interview, TCM president Rhett Ross indicated belief that the aviation industry will be "forced out" of using 100LL in the near future, leaving automotive fuel and jet fuel as the only alternatives. In May 2010, TCM announced that they had licenced development of the SMA SR305 diesel engine.[32] [33][34]

In November 2008, National Air Transportation Association president Jim Coyne indicated that the environmental impact of aviation is expected to be a big issue over the next few years and will result in the phase out of 100LL because of its lead content.[35]

By May 2012, the US Federal Aviation Administration (FAA Unleaded Avgas Transition rulemaking committee) had put together a plan in conjunction with industry to replace leaded avgas with an unleaded alternative within 11 years. Given the progress already made on 100SF and G100UL, the replacement time might be shorter than that 2023 estimate. Each candidate fuel must meet a checklist of 12 fuel specification parameters and 4 distribution and storage parameters. The FAA has requested a maximum of US$60M to fund the administration of the changeover.[36]

New unleaded fuel grades


The firm Airworthy AutoGas tested an ethanol-free premium auto gas on a Lycoming O-360A4M in 2013. The fuel is certified under Lycoming 1070S and ATSM D4814.[37]


Unleaded 94-octane fuel (94UL) is essentially 100LL without the lead. In March 2009, Teledyne Continental Motors (TCM) announced they had tested a 94UL fuel that might be the best replacement for 100LL. This 94UL meets the avgas specification including vapor pressure but has not been completely tested for detonation qualities in all Continental engines or under all conditions. Flight testing has been conducted in a IO-550-B powering a Beechcraft Bonanza and ground testing in Continental O-200, 240, O-470, and O-520 engines. In May 2010, TCM indicated that despite industry skepticism, they are proceeding with 94UL and that certification is expected in mid-2013.[38][39]

In June 2010, Lycoming Engines indicated their opposition to 94UL. Company general manager Michael Kraft stated that aircraft owners do not realize how much performance would be lost with 94UL and characterized the decision to pursue 94UL as a mistake that could cost the aviation industry billions in lost business. Lycoming believes the industry should be pursuing 100UL instead. The Lycoming position is supported by aircraft type clubs representing owners of aircraft that would be unable to run on lower octane fuel. In June 2010, clubs such as the American Bonanza Society, the Malibu Mirage Owners and Pilots Association, and the Cirrus Owners and Pilots Association collectively formed the Clean 100 Octane Coalition to represent them on this issue and push for unleaded 100 octane avgas.[40][41][42][43]

100SF by Swift Fuel

"Swift Fuel" redirects here.

John and Mary-Louise Rusek founded Swift Enterprises in 2001 to develop renewable fuels and hydrogen fuel cells. By 2006, they had submitted a sample of "Swift 142" to Oracle Airmotive Research & Development of Delphi, Indiana, which found that the fuel gave a 10% longer run time than an equal volume of 100LL fuel in the 100 hp (75 kW) engine of a Bakeng Deuce aircraft.[44] The following year, Swift Enterprises (now its subsidiary Swift Fuels, LLC) filed US and international patent applications for non-alcohol Renewable Engine Fuels of a variety of octane ratings, to be blended from "one or more low carbon number esters, one or more pentosan-derivable furans, one or more aromatic hydrocarbon, one or more C4-C10 straight chain alkanes derivable from polysaccharides, and one or more bio-oils... [and, optionally,] triethanolamine", which could be derived from biomass fermentation.[45] Swift Enterprises initiated Carroll County Swift Development Inc.[46] to plan a 2,500-square-foot (230 m2) pilot plant at the Delphi Municipal Airport in Indiana,[47] and submitted fuel to the FAA for testing.[48][49] [50][51]

In 2008, an article by technology writer and aviation enthusiast Robert X Cringely stating that the fuel was renewable, cleaner-burning, and potentially cheaper than avgas or even mogas attracted popular attention to the fuel.[52] AOPA's Dave Hirschman took a cross-country flight using the fuel in fall of 2009 stating "Swift Fuel has made the leap from the purely theoretical to a real product, and it appears to hold great promise for shifting GA to an unleaded, non-petroleum-based future."[53] Swift Enterprises claimed that the fuel could be manufactured for USD$2 per gallon although its cost per gallon for laboratory batches was US$60.[48][54] Swift Enterprises' website claims their product has 15% more volumetric energy for a 15-25% increase in range over 100LL. The FAA found Swift Fuel to have a motor octane number of 104.4, 96.3% of the energy per unit of mass, and 113% of the energy per unit of volume as 100LL, and meets most of the ASTM D910 standard for leaded aviation fuel. Following tests in two Lycoming engines, the FAA concluded it performs better than 100LL in detonation testing and will provide a fuel savings of 8% per unit of volume, though it weighs 1 pound per gallon (120 g/l) more than 100LL. GCFID testing showed the fuel to be made primarily of two components — one about 85% by weight and the other about 14% by weight.[55][56] Soon afterward, AVweb reported that Continental had begun the process of certifying several of its engines to use the new fuel.[57]

Swift Fuel 100SF has been criticized by aviation analysts on grounds including that the forecast price is likely unattainable, that the US$2 per gallon is a refinery price and not a retail price, and that biomass yields critical to the project are unproven. In March 2009, Paul Bertorelli of Aviation Consumer termed it "one that's still a long shot" as a replacement for 100LL avgas, but conceded "... if Swift Fuel's real manufacturing cost is $3 a gallon and that translates to $5 or a little more at retail, they've got a player. [General aviation] in the U.S. can and has adapted to $5 avgas. If Swift can deliver, this project could have legs."[58]

In December 2009, 100SF was approved as a test fuel by ASTM International allowing the company to pursue certification testing. Mary Rusek, president and co-owner of Swift Enterprises predicted at that time that "100SF will be comparably priced, environmentally friendlier, and more fuel-efficient than other general aviation fuels on the market".[59] [60]

In February 2010, AVweb reported that Swift's production costs had not proven economical; in May 2010, it was confirmed that the initial retail cost would be about US$10 per gallon. John Rusek, president of Swift Enterprises "strongly disputes" the $10 per gallon figure and insists that 100SF can be produced for the same price as 100LL. In July 2010, company representative David Perme indicated that 100SF could be made from either biomass or natural gas as a feedstock for its base constituent of acetone. He stated that this flexibility should produce a fuel that is US$5–6 per gallon.[61][62][63][64]

Swift's patents indicate that the product is a binary fuel made from acetone. The acetone is converted into a blend of isopentane and mesitylene to make the final fuel. 100SF can be made from biomass or from petrochemical bases, including natural gas.[64]

In August 2010, the FAA's William J. Hughes Technical Center in Atlantic City, New Jersey, issued a report on endurance testing of 100SF carried out on a new Lycoming IO-540 engine involving 150 hrs of run time. Other than deterioration of the fuel pump, the tests were satisfactory.[65]

In October 2010, Purdue University reported on 100SF as part of their program of testing. Purdue used six aviation piston engines, including the highest octane requirement engine, a Lycoming TIO-540-J2BD and a 1933 model Ranger L-440 which requires 65-octane. David Stanley, principal investigator, stated, "Swift Fuel appears promising as a replacement for 100LL general aviation fuel".[66]

In 2011, "ASTM International approved a new fuel specification, ASTM D7719 Standard Specification for High Octane Unleaded Test Fuel, for Grade UL102 unleaded aviation gasoline." The company claims their fuel meets the UL102 standard, which allows "Swift to test UL102 in non-Experimental aircraft". [67]


In February 2010, General Aviation Modifications Inc. announced that they were in the process of developing a 100LL replacement to be called G100UL ("unleaded"). This fuel is made by blending existing refinery products and produces detonation margins comparable to 100LL. The new fuel is slightly more dense than 100LL, but has a 3.5% higher thermodynamic output. G100UL is compatible with 100LL and can be mixed with it in aircraft tanks for use. The production economics of this new fuel have not been confirmed but it is anticipated that it will cost at least as much as 100LL.[61][68]

In demonstrations held in July 2010, G100UL performed better than 100LL that just meets the minimum specification and equal to average production 100LL.[69]

Environmental regulation

TEL found in leaded avgas and its combustion products are potent neurotoxins that have been shown in scientific research to interfere with brain development in children. The United States Environmental Protection Agency (EPA) has noted that exposure to even very low levels of lead contamination has been conclusively linked to loss of IQ in children's brain function tests, thus providing a high degree of motivation to eliminate lead and its compounds from the environment.[70] [71]

On 16 November 2007, the environmental group Friends of the Earth formally petitioned the EPA, asking them to regulate leaded avgas. The EPA responded with a notice of petition for rulemaking.[10]

The notice of petition stated:

The public comment period on this petition closed on 17 March 2008.[72]

Under a federal court order to set a new standard by 15 October 2008, the EPA cut the acceptable limits for atmospheric lead from the previous standard of 1.5 µg/m3 to 0.15 micrograms per cubic meter. This was the first change to the standard since 1978 and represents an order of magnitude reduction over previous levels. The new standard requires the 16,000 remaining USA sources of lead, which include lead smelting, airplane fuels, military installations, mining and metal smelting, iron and steel manufacturing, industrial boilers and process heaters, hazardous waste incineration, and production of batteries, to reduce their emissions by October 2011.[70][71][73]

The EPA's own studies have shown that to prevent a measurable decrease in IQ for children deemed most vulnerable, the standard needs to be set much lower, to 0.02 µg/m3. The EPA identified avgas as one of the most "significant sources of lead".

At an EPA public consultation held in June 2008 on the new standards, Andy Cebula, the Aircraft Owners and Pilots Association's executive vice president of government affairs stated that general aviation plays a valuable role in the USA economy and any changes in lead standards that would change the current composition of avgas would have a "direct impact on the safety of flight and the very future of light aircraft in this country".[74]

In December 2008, AOPA filed formal comments to the new EPA regulations. AOPA indicated that piston-powered aircraft produce "one-tenth of 1 percent" of national lead emissions and that they are 0.55% of all transportation emissions. AOPA has asked the EPA to account for the cost and the safety issues involved with removing lead from avgas. They cited that the aviation sector employs more than 1.3 million people in the USA and has an economic direct and indirect effect that "exceeds $150 billion annually". AOPA interprets the new regulations as not affecting general aviation as they are currently written.[75]

Publication in the USA Federal Register of an Advance Notice of Proposed Rulemaking by the USA EPA occurred in April 2010. The EPA indicated: "This action will describe the lead inventory related to use of leaded avgas, air quality and exposure information, additional information the Agency is collecting related to the impact of lead emissions from piston-engine aircraft on air quality and will request comments on this information."[76][77]

Despite assertions in the media that leaded avgas will be eliminated in the USA by 2017 at the latest date, the EPA confirmed in July 2010 that there is no phase-out date and that setting one would be an FAA responsibility as the EPA has no authority over avgas. The FAA administrator stated that regulating lead in avgas is an EPA responsibility, resulting in widespread criticism of both organizations for causing confusion and delaying solutions.[78] [79] [80] [81] [82]

In April 2011 at Sun 'n Fun, Pete Bunce, head of the General Aviation Manufacturers Association (GAMA) and Craig Fuller, president and CEO of the Aircraft Owners and Pilots Association indicated that they both are confident that leaded avgas will not be eliminated until a suitable replacement is in place. "There is no reason to believe 100 low-lead will become unavailable in the foreseeable future," Fuller stated.[83]

Final results from EPA's lead modeling study at the Santa Monica Airport shows off airport levels below current 150 ng/m3 and possible future 20 ng/m3 levels.[84] 15 of 17 airports monitored during a year-long study in the USA by the EPA have lead emissions well below the current National Ambient Air Quality Standard (NAAQS) for lead.[85]

Other uses

Avgas is occasionally used in amateur auto racing cars as its octane rating is higher than automotive gasoline thus allowing the engines to run at higher compression ratios.

See also


This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from World eBook Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.