Illustration from Army Service Corps Training on Mechanical Transport, (1911), Fig. 112 Transmission of motion and force by gear wheels, compound train
A gear train is a mechanical system formed by mounting gears on a frame so that the teeth of the gears engage.
Gear teeth are designed to ensure the pitch circles of engaging gears roll on each other without slipping, providing a smooth transmission of rotation from one gear to the next.^{[1]}
The transmission of rotation between contacting toothed wheels can be traced back to the involute tooth yielded a standard gear design that provides a constant speed ratio.
Features of gears and gear trains include:
An Agricola illustration from 1580 showing a toothed wheel that engages a slotted cylinder to form a gear train that transmits power from a humanpowered treadmill to mining pump.
Contents

Mechanical advantage 1

Analysis using virtual work 2

Gear trains with two gears 3

Speed ratio 4

Torque ratio 5

Idler gears 6

Belt drives 7

Automotive applications 8

Example 8.1

Wideratio vs. closeratio transmission 8.2

See also 9

References 10

External links 11
Mechanical advantage
Gear teeth are designed so that the number of teeth on a gear is proportional to the radius of its pitch circle, and so that the pitch circles of meshing gears roll on each other without slipping. The speed ratio for a pair of meshing gears can be computed from ratio of the radii of the pitch circles and the ratio of the number of teeth on each gear.
Two meshing gears transmit rotational motion.
The velocity v of the point of contact on the pitch circles is the same on both gears, and is given by

v = r_A \omega_A = r_B \omega_B, \!
where input gear A has radius r_{A} and meshes with output gear B of radius r_{B}, therefore,

\frac{\omega_A}{\omega_B} = \frac{r_B}{r_A} = \frac{N_B}{N_A}.
where N_{A} is the number of teeth on the input gear and N_{B} is the number of teeth on the output gear.
The mechanical advantage of a pair of meshing gears for which the input gear has N_{A} teeth and the output gear has N_{B} teeth is given by

MA = \frac{T_B}{T_A} = \frac{N_B}{N_A}.
This shows that if the output gear G_{B} has more teeth than the input gear G_{A}, then the gear train amplifies the input torque. And, if the output gear has fewer teeth than the input gear, then the gear train reduces the input torque.
If the output gear of a gear train rotates more slowly than the input gear, then the gear train is called a speed reducer. In this case, because the output gear must have more teeth than the input gear, the speed reducer amplifies the input torque.
Analysis using virtual work
For this analysis, we consider a gear train that has one degreeoffreedom, which means the angular rotation of all the gears in the gear train are defined by the angle of the input gear.
The size of the gears and the sequence in which they engage define the ratio of the angular velocity ω_{A} of the input gear to the angular velocity ω_{B} of the output gear, known as the speed ratio, or gear ratio, of the gear train. Let R be the speed ratio, then

\frac{\omega_A}{\omega_B} = R.
The input torque T_{A} acting on the input gear G_{A} is transformed by the gear train into the output torque T_{B} exerted by the output gear G_{B}. If we assume, that the gears are rigid and that there are no losses in the engagement of the gear teeth, then the principle of virtual work can be used to analyze the static equilibrium of the gear train.
Let the angle θ of the input gear be the generalized coordinate of the gear train, then the speed ratio R of the gear train defines the angular velocity of the output gear in terms of the input gear, that is

\omega_A = \omega, \quad \omega_B = \omega/R.\!
The formula for the generalized force obtained from the principle of virtual work with applied torques yields^{[2]}

F_\theta = T_A \frac{\partial\omega_A}{\partial\omega}  T_B \frac{\partial \omega_B}{\partial\omega}= T_A  T_B/R = 0.
The mechanical advantage of the gear train is the ratio of the output torque T_{B} to the input torque T_{A}, and the above equation yields

MA = \frac{T_B}{T_A} = R.
Thus, the speed ratio of a gear train also defines its mechanical advantage. This shows that if the input gear rotates faster than the output gear, then the gear train amplifies the input torque. And, if the input gear rotates slower than the output gear, then the gear train reduces the input torque.
Gear trains with two gears
The simplest example of a gear train has two gears. The "input gear" (also known as drive gear) transmits power to the "output gear" (also known as driven gear). The input gear will typically be connected to a power source, such as a motor or engine. In such an example, the power output of the output (driven) gear depends on the ratio of the dimensions of the two gears.
Two meshing gears transmit rotational motion.
Formula
The teeth on gears are designed so that the gears can roll on each other smoothly (without slipping or jamming). In order for two gears to roll on each other smoothly, they must be designed so that the velocity at the point of contact of the two pitch circles (represented by v) is the same for each gear.
Mathematically, if the input gear G_{A} has the radius r_{A} and angular velocity \omega_A \!, and meshes with output gear G_{B} of radius r_{B} and angular velocity \omega_B \!, then:

v = r_A \omega_A = r_B \omega_B, \!
The number of teeth on a gear is proportional to the radius of its pitch circle, which means that the ratios of the gears' angular velocities, radii, and number of teeth are equal. Where N_{A} is the number of teeth on the input gear and N_{B} is the number of teeth on the output gear, the following equation is formed:

\frac{\omega_A}{\omega_B} = \frac{r_B}{r_A} = \frac{N_B}{N_A}.
This shows that a simple gear train with two gears has the gear ratio R given by

R = \frac{\omega_A}{\omega_B} = \frac{N_B}{N_A}.
This equation shows that if the number of teeth on the output gear G_{B} is larger than the number of teeth on the input gear G_{A}, then the input gear G_{A} must rotate faster than the output gear G_{B}.
Speed ratio
Gear teeth are distributed along the circumference of the pitch circle so that the thickness t of each tooth and the space between neighboring teeth are the same. The pitch p of a gear, which is the distance between equivalent points on neighboring teeth along the pitch circle, is equal to twice the thickness of a tooth,

p=2t.\!
The pitch of a gear G_{A} can be computed from the number of teeth N_{A} and the radius r_{A} of its pitch circle

p = \frac{2\pi r_A}{N_A}.
In order to mesh smoothly two gears G_{A} and G_{B} must have the same sized teeth and therefore they must have the same pitch p, which means

p = \frac{2\pi r_A}{N_A} = \frac{2\pi r_B}{N_B}.
This equation shows that the ratio of the circumference, the diameters and the radii of two meshing gears is equal to the ratio of their number of teeth,

\frac{r_B}{r_A} = \frac{N_B}{N_A}.
The speed ratio of two gears rolling without slipping on their pitch circles is given by,

R =\frac{\omega_A}{\omega_B}=\frac{r_B}{r_A},
therefore

R = \frac{\omega_A}{\omega_B} = \frac{N_B}{N_A}.
In other words, the gear ratio, or speed ratio, is inversely proportional to the radius of the pitch circle and the number of teeth of the input gear.
Torque ratio
A gear train can be analyzed using the principle of virtual work to show that its torque ratio, which is the ratio of its output torque to its input torque, is equal to the gear ratio, or speed ratio, of the gear train.
This means that the input torque Τ_{A} applied to the input gear G_{A} and the output torque Τ_{B} on the output gear G_{B} are related by the ratio

R = \frac{T_B}{T_A},
where R is the gear ratio of the gear train.
The torque ratio of a gear train is also known as its mechanical advantage

\mathit{MA} = \frac{T_B}{T_A}.
Idler gears
In a sequence of gears chained together, the ratio depends only on the number of teeth on the first and last gear. The intermediate gears, regardless of their size, do not alter the overall gear ratio of the chain. However, the addition of each intermediate gear reverses the direction of rotation of the final gear.
An intermediate gear which does not drive a shaft to perform any work is called an idler gear. Sometimes, a single idler gear is used to reverse the direction, in which case it may be referred to as a reverse idler. For instance, the typical automobile manual transmission engages reverse gear by means of inserting a reverse idler between two gears.
Idler gears can also transmit rotation among distant shafts in situations where it would be impractical to simply make the distant gears larger to bring them together. Not only do larger gears occupy more space, the mass and rotational inertia (moment of inertia) of a gear is proportional to the square of its radius. Instead of idler gears, a toothed belt or chain can be used to transmit torque over distance.
Formula
If a simple gear train has three gears, such that the input gear G_{A} meshes with an intermediate gear G_{I} which in turn meshes with the output gear G_{B}, then the pitch circle of the intermediate gear rolls without slipping on both the pitch circles of the input and output gears. This yields the two relations

\frac{\omega_A}{\omega_I} = \frac{N_I}{N_A}, \quad \frac{\omega_I}{\omega_B} = \frac{N_B}{N_I}.
The speed ratio of this gear train is obtained by multiplying these two equations to obtain

R = \frac{\omega_A}{\omega_B} = \frac{N_B}{N_A}.
Notice that this gear ratio is exactly the same as for the case when the gears G_{A} and G_{B} engaged directly. The intermediate gear provides spacing but does not affect the gear ratio. For this reason it is called an idler gear. The same gear ratio is obtained for a sequence of idler gears and hence an idler gear is used to provide the same direction to rotate the driver and driven gear, if the driver gear moves in clockwise direction, then the driven gear also moves in the clockwise direction with the help of the idler gear.
Example
2 gears and an
idler gear on a piece of farm equipment, with a ratio of 42/13 = 3.23:1
In the photo, assuming that the smallest gear is connected to the motor, it is called the drive gear or input gear. The somewhat larger gear in the middle is called an idler gear. It is not connected directly to either the motor or the output shaft and only transmits power between the input and output gears. There is a third gear in the upperright corner of the photo. Assuming that that gear is connected to the machine's output shaft, it is the output or driven gear.
The input gear in this gear train has 13 teeth and the idler gear has 21 teeth. Considering only these gears, the gear ratio between the idler and the input gear can be calculated as if the idler gear was the output gear. Therefore, the gear ratio is driven/drive = 21/13 ≈1.62 or 1.62:1.
At this ratio it means that the drive gear must make 1.62 revolutions to turn the driven gear once. It also means that for every one revolution of the driver, the driven gear has made 1/1.62, or 0.62, revolutions. Essentially, the larger gear turns slower.
The third gear in the picture has 42 teeth. The gear ratio between the idler and third gear is thus 42/21, or 2:1, and hence the final gear ratio is 1.62x2≈3.23. For every 3.23 revolutions of the smallest gear, the largest gear turns one revolution, or for every one revolution of the smallest gear, the largest gear turns 0.31 (1/3.23) revolution, a total reduction of about 1:3.23 (Gear Reduction Ratio (GRR) = 1/Gear Ratio (GR)).
Since the idler gear contacts directly both the smaller and the larger gear, it can be removed from the calculation, also giving a ratio of 42/13≈3.23. The idler gear serves to make both the drive gear and the driven gear rotate in the same direction, but confers no mechanical advantage.
Belt drives
Belts can have teeth in them also and be coupled to gearlike pulleys. Special gears called sprockets can be coupled together with chains, as on bicycles and some motorcycles. Again, exact accounting of teeth and revolutions can be applied with these machines.
For example, a belt with teeth, called the timing belt, is used in some internal combustion engines to synchronize the movement of the camshaft with that of the crankshaft, so that the valves open and close at the top of each cylinder at exactly the right time relative to the movement of each piston. A chain, called a timing chain, is used on some automobiles for this purpose, while in others, the camshaft and crankshaft are coupled directly together through meshed gears. Regardless of which form of drive is employed, the crankshaft to camshaft gear ratio is always 2:1 on fourstroke engines, which means that for every two revolutions of the crankshaft the camshaft will rotate once.
Automotive applications
Illustration of gears of an automotive transmission
Automobile drivetrains generally have two or more major areas where gearing is used. Gearing is employed in the transmission, which contains a number of different sets of gears that can be changed to allow a wide range of vehicle speeds, and also in the differential, which contains the final drive to provide further speed reduction at the wheels. In addition, the differential contains further gearing that splits torque equally between the two wheels while permitting them to have different speeds when travelling in a curved path. The transmission and final drive might be separate and connected by a driveshaft, or they might be combined into one unit called a transaxle. The gear ratios in transmission and final drive are important because different gear ratios will change the characteristics of a vehicle's performance.
Example
A 2004 Chevrolet Corvette C5 Z06 with a sixspeed manual transmission has the following gear ratios in the transmission:
Gear

Ratio

1st gear

2.97:1

2nd gear

2.07:1

3rd gear

1.43:1

4th gear

1.00:1

5th gear

0.84:1

6th gear

0.56:1

reverse

3.38:1

In 1st gear, the engine makes 2.97 revolutions for every revolution of the transmission’s output. In 4th gear, the gear ratio of 1:1 means that the engine and the transmission's output rotate at the same speed. 5th and 6th gears are known as overdrive gears, in which the output of the transmission is revolving faster than the engine's output.
The Corvette above has an axle ratio of 3.42:1, meaning that for every 3.42 revolutions of the transmission’s output, the wheels make one revolution. The differential ratio multiplies with the transmission ratio, so in 1st gear, the engine makes 10.16 revolutions for every revolution of the wheels.
The car’s tires can almost be thought of as a third type of gearing. This car is equipped with 295/3518 tires, which have a circumference of 82.1 inches. This means that for every complete revolution of the wheel, the car travels 82.1 inches (209 cm). If the Corvette had larger tires, it would travel farther with each revolution of the wheel, which would be like a higher gear. If the car had smaller tires, it would be like a lower gear.
With the gear ratios of the transmission and differential, and the size of the tires, it becomes possible to calculate the speed of the car for a particular gear at a particular engine RPM.
For example, it is possible to determine the distance the car will travel for one revolution of the engine by dividing the circumference of the tire by the combined gear ratio of the transmission and differential.
d = \frac{c_t}{gr_t \times gr_d}
It is also possible to determine a car's speed from the engine speed by multiplying the circumference of the tire by the engine speed and dividing by the combined gear ratio.
v_c = \frac{c_t \times v_e}{gr_t \times gr_d}
Gear

Distance per engine revolution

Speed per 1000 RPM

1st gear

8.1 in (210 mm)

7.7 mph (12.4 km/h)

2nd gear

11.6 in (290 mm)

11.0 mph (17.7 km/h)

3rd gear

16.8 in (430 mm)

15.9 mph (25.6 km/h)

4th gear

24.0 in (610 mm)

22.7 mph (36.5 km/h)

5th gear

28.6 in (730 mm)

27.1 mph (43.6 km/h)

6th gear

42.9 in (1,090 mm)

40.6 mph (65.3 km/h)

Wideratio vs. closeratio transmission
A closeratio transmission is a transmission in which there is a relatively little difference between the gear ratios of the gears. For example, a transmission with an engine shaft to drive shaft ratio of 4:1 in first gear and 2:1 in second gear would be considered wideratio when compared to another transmission with a ratio of 4:1 in first and 3:1 in second. This is because the closeratio transmission has less of a progression between gears. For the wideratio transmission, the first gear ratio is 4:1 or 4, and in second gear it is 2:1 or 2, so the progression is equal to 4/2 = 2 (or 200%). For the closeratio transmission, first gear has a 4:1 ratio or 4, and second gear has a ratio of 3:1 or 3, so the progression between gears is 4/3, or 133%. Since 133% is less than 200%, the transmission with the smaller progression between gears is considered closeratio. However, the difference between a closeratio and wideratio transmission is subjective and relative.^{[3]}
Closeratio transmissions are generally offered in sports cars, sport bikes, and especially in race vehicles, where the engine is tuned for maximum power in a narrow range of operating speeds, and the driver or rider can be expected to shift often to keep the engine in its power band.
Factory 4speed or 5speed transmission ratios generally have a greater difference between gear ratios and tend to be effective for ordinary driving and moderate performance use. Wider gaps between ratios allow a higher 1st gear ratio for better manners in traffic, but cause engine speed to decrease more when shifting. Narrowing the gaps will increase acceleration at speed, and potentially improve top speed under certain conditions, but acceleration from a stopped position and operation in daily driving will suffer.
Range is the torque multiplication difference between 1st and 4th gears; widerratio gearsets have more, typically between 2.8 and 3.2. This is the single most important determinant of lowspeed acceleration from stopped.
Progression is the reduction or decay in the percentage drop in engine speed in the next gear, for example after shifting from 1st to 2nd gear. Most transmissions have some degree of progression in that the RPM drop on the 12 shift is larger than the RPM drop on the 23 shift, which is in turn larger than the RPM drop on the 34 shift. The progression may not be linear (continuously reduced) or done in proportionate stages for various reasons, including a special need for a gear to reach a specific speed or RPM for passing, racing and so on, or simply economic necessity that the parts were available.
Range and progression are not mutually exclusive, but each limits the number of options for the other. A wide range, which gives a strong torque multiplication in 1st gear for excellent manners in lowspeed traffic, especially with a smaller motor, heavy vehicle, or numerically low axle ratio such as 2.50, means that the progression percentages must be high. The amount of engine speed, and therefore power, lost on each upshift is greater than would be the case in a transmission with less range, but less power in 1st gear. A numerically low 1st gear, such as 2:1, reduces available torque in 1st gear, but allows more choices of progression.
There is no optimal choice of transmission gear ratios or a final drive ratio for best performance at all speeds, as gear ratios are compromises, and not necessarily better than the original ratios for certain purposes.
See also
References

^ Uicker, J. J.; G. R. Pennock; J. E. Shigley (2003). Theory of Machines and Mechanisms. New York: Oxford University Press.

^ Paul, B. (1979). Kinematics and Dynamics of Planar Machinery. Prentice Hall.

^ Cangialosi, Paul (2001). "TechZone Article: Wide and Close Gear Ratios". 5speeds.com. Medatronics. Retrieved 28 October 2012.
External links

Gear ratio at How Stuff Works

Online Motorcycle gear train calculator with Help pages


Systems



Shapes



Geartooth profiles



Mechanics



Examples



See also



This article was sourced from Creative Commons AttributionShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, EGovernment Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a nonprofit organization.