World Library  
Flag as Inappropriate
Email this Article

Involute gear

Article Id: WHEBN0000351293
Reproduction Date:

Title: Involute gear  
Author: World Heritage Encyclopedia
Language: English
Subject: Gear, Gears, Hobbing, Pressure angle, Instant centre of rotation
Collection: Gears
Publisher: World Heritage Encyclopedia
Publication
Date:
 

Involute gear

Two involute gears, the left driving the right: Blue arrows show the contact forces between them. The force line (or Line of Action) runs along a tangent common to both base circles. (In this situation, there is no force, and no contact needed, along the opposite common tangent not shown.) The involutes here are traced out in converse fashion: points (of contact) move along the stationary force-vector "string" as if unwound from the left rotating base circle, and wound onto the right rotating base circle.

The involute gear profile, originally designed by Leonhard Euler,[1] is the most commonly used system for gearing today, with cycloidal gearing still used for some specialties such as clocks. In an involute gear, the profiles of the teeth are involutes of a circle. (The involute of a circle is the spiraling curve traced by the end of an imaginary taut string unwinding itself from that stationary circle called the base circle.)

Irrespective of whether a gear is spur or helical, in every plane of the involute gears the contact between a pair of gear teeth occurs at a single instantaneous point (see figure at right) where two involutes of the same spiral hand meet. Contact on the other side of the teeth is where both involutes are of the other spiral hand. Rotation of the gears causes the location of this contact point to move across the respective tooth surfaces. The tangent at any point of the curve is perpendicular to the generating line irrespective of the mounting distance of the gears. Thus the line of the force follows the generating line, and is thus tangent to the two base circles, and is known as the Line of Action (also called Pressure Line or Line of Contact). When this is true, the gears obey the Fundamental Law of Gearing:[2]
The angular velocity ratio between two gears of a gearset must remain constant throughout the mesh.

This property is required for smooth transmission of power with minimal speed or torque variations as pairs of teeth go into or come out of mesh, but is not required for low-speed gearing.

Where the line of action crosses the line between the two centres it is called the Pitch Point of the gears, where there is no sliding contact.

The Pressure Angle is the acute angle between the line of action and a normal to the line connecting the gear centers. The pressure angle of the gear varies according to the position on the involute shape, but pairs of gears must have the same pressure angle for the teeth to mesh properly, so specific portions of the involute must be matched.

While manufacturers can produce any pressure angle, the most common stock gears have a 20° pressure angle, with 14½° and 25° pressure angle gears being much less common.[3] Increasing the pressure angle increases the width of the base of the gear tooth, leading to greater strength and load carrying capacity. Decreasing the pressure angle provides lower backlash, smoother operation and less sensitivity to manufacturing errors.[4]

Only used in limited situations are helical involute gears, where the spirals of the two involutes are of different 'hand' and the Line of Action is the external tangents to the base circles (like a normal belt drive whereas normal gears are like a crossed-belt drive), and the gears rotate in the same direction,[5][6] and there is sliding at the contact point which gives inefficiency and thus can be used in limited slip differentials.[7][8] These cannot be spur gears unless they comprise multiple sectors of gears, and are otherwise helical, but the meshing gears are of the same helix angle rather than of opposite hand.

References

  1. ^
  2. ^
  3. ^
  4. ^
  5. ^
  6. ^ US 5129276, Fahy, Arthur J. & Neil Gillies, "Meshing gear members" 
  7. ^ US 4831890, Mercier, Jacques & Daniel Valentin, "Differential device" 
  8. ^ US 5071395, Fahy, Arthur J. & Neil Gillies, "Differential gear mechanism" 

External links

  • Kinematic Models for Design Digital Library (KMODDL)
    Movies and photos of hundreds of working mechanical-systems models at Cornell University. Also includes an e-book library of classic texts on mechanical design and engineering.
  • Involute gear at How Stuff Works - with animation
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.
 



Copyright © World Library Foundation. All rights reserved. eBooks from World eBook Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.