World Library  
Flag as Inappropriate
Email this Article

Warded lock

Article Id: WHEBN0000250415
Reproduction Date:

Title: Warded lock  
Author: World Heritage Encyclopedia
Language: English
Subject: Skeleton key, Lock (security device), Lock picking, Locksmithing, Key control
Collection: Locks (Security Device)
Publisher: World Heritage Encyclopedia
Publication
Date:
 

Warded lock

The key enters the lock through a keyhole.
When the key is fully inserted, a cavity in the tip of the key fits over a cylindrical post inside the lock. This provides a pivot point about which the key can rotate.
The notches in the key align with the obstructions, or wards, allowing it to rotate freely. In rotating, the key may then activate a lever or sliding bolt to open the lock.

A warded lock (also called a ward lock) is a type of lock that uses a set of obstructions, or wards, to prevent the lock from opening unless the correct key is inserted. The correct key has notches or slots corresponding to the obstructions in the lock, allowing it to rotate freely inside the lock. Large warded locks are still in use today in the UK and Ireland for internal and external doors though mainly in 'heritage' sites such as ancient monuments and churches to preserve original features, primary security being provided by other means. Warded locks in America are commonly used in inexpensive padlocks, cabinet locks, and other low-security applications, since a well-designed skeleton key can successfully open a wide variety of warded locks.

History

The warded lock is one of the most ancient lock designs still in modern use. During the Middle Ages they were used prolifically on monasteries where, because money and time were not issues, their complexity grew. All had the same inherent problem: by removing most parts of the key, except the bare minimum to operate the bolt, and so producing a skeleton key, the wards could be bypassed.

Design

In the most basic warded lock, a set of obstructions, often consisting of concentric plates protruding outwards, blocks the rotation of a key not designed for that lock. Warded locks may have one simple ward, or many intricate wards with bends and complex protrusions; the principle remains the same. Unless the notches or slots in the key correspond to the wards in the lock, the key will strike an obstruction and will not turn.

Additionally, a series of grooves on either side of the key's blade limit the type of lock the key can slide into. As the key slides into the lock through the keyway, the wards align with the grooves in the key's profile to allow or deny entry into the lock cylinder. Although this is not commonly recognized when discussing warded locks, it is more applicable to current locksmithing applications such as pin-tumbler or wafer-tumbler locks.

In double sided locks the centre of the key shaft is solid and protrudes past the end of the bit which slots into a hole on the opposite side of the lock. Double sided ward locks nearly always have perfectly symmetrical bits. For single sided locks a cylindrical post is typically located in the center of the lock. Its purpose is to provide a point of leverage for rotating the key, and to help correctly align the key with the wards. The key has a corresponding hole which fits over the post.

When the correct key is inserted, it will clear the wards and rotate about the center post. The key may then strike a lever, activating a latch or sliding bolt, or it may itself push against the latch or bolt. In a double acting lever lock, the key may additionally push against a spring-loaded lever which holds the sliding bolt in place.

This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.
 



Copyright © World Library Foundation. All rights reserved. eBooks from World eBook Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.